casting ring
英 [ˈkɑːstɪŋ rɪŋ]
美 [ˈkæstɪŋ rɪŋ]
网络 铸造环
双语例句
- An Investigation on Material and Casting Method of STD Cast Iron Piston Ring
STD活塞环材料及铸造工艺的研究 - Influence of different casting positions in the cast ring on the metal-porcelain bond strength
铸件在铸圈中不同包埋位置对金瓷结合的影响 - The successful experience of thick steel plates to replace casting of hydraulic turbine runner lower ring
水轮机转轮下环由厚钢板卷焊替代铸件的成功经验 - The analysis results indicate that the stress of steel arch centering satisfies the requirements of strength during different stages of casting main arch ring.
分析结果表明，在主拱圈砌筑的各个节段，钢拱架的应力均满足强度要求。 - Producing Glass-Al Composite by Centrifugal Casting Development of Heavy Centrifugal Composite Roll Ring
离心铸造制备玻璃&铝复合材料大型离心复合辊套的生产研制过程 - Casting Production of Nodular Iron Piston Ring
球墨铸铁活塞环铸件的生产 - The Casting of the Rolling Ring
滚圈的铸造生产 - Abstract Producing the flywheel gear ring with a flat steel by an old flash butt welding process is replaced by a casting blank and rolling to form the gear ring process, not only the investment is saved but also the product quality is improved.
采用铸造制坯、辗环成形新工艺替代用扁钢闪光对焊生产飞轮齿环的老工艺，不仅节省了投资，而且提高了产品质量。 - TiC/ ZA43 composite was fabricated by stirring casting technique. The tribology properties of the composites were studied using a block on ring apparatus.
采用搅拌铸造法制备了TiC/ZA43复合材料，用环-块摩擦磨损试验机测试了连续润滑条件下复合材料的滑动摩擦磨损性能。 - To construct foundations for large storage tanks by casting ring beam after backfilling
先回填后浇筑环梁施工大型储罐基础 - That is: ( 1) to make the electroslag casting ring; ( 2) high temperature controlled hot deformation followed by controlled cooling ( i.e. high temperature thermomechanical treatment); ( 3) cold deformation strengthening.
它由如下三步组成：（1）电渣熔铸环坯→（2）高温控制热变形和控制冷却（即高温形变热处）→（3）冷变形强化。 - It utilizes design software Pro/ E to create three-dimensional modeling for casting steel bottom ring and bent axle, uses the casting numerical simulation software MAGMA to carry on the filling and solidification numerical simulation analysis of castings in this paper.
本文利用Pro/E设计软件对铸钢件底环、曲轴进行了三维建模，运用MAGMA铸造数值模拟软件进行铸件充型凝固过程的数值模拟分析。 - Improvement on the Casting Structure and Foundry Process Design of A& ring Casting
对A环铸件设计和铸造工艺的改进 - On the Melting and Casting and Heat Treatment of the Piston Ring with High Elasticity and Stability in Ship Engines
一种高弹力、高稳定性船用发动机活塞环的熔铸及热处理 - The Design of Investment Casting Die of Integral Guiding Device of Internal Ring
基于UG的导向器类零件内环精铸模具设计 - The Single Casting of Piston Ring s Without Risers
活塞环无冒口单体铸造 - Casting Process for Heavy Gear Ring of Raw Material Millstones Used for Cement Plant
水泥厂原料磨大齿圈铸造技术 - The Squeeze Casting Technology of Φ 120mm Insert Ring Piston with Double Slot
Φ120mm双环槽镶圈活塞的挤压铸造 - Specially, CAE technology on squeeze casting mould develops slowly. And the research mainly concentrates on melt flowing and forming process analysis in near-closed hollow ring. Researches on control analysis about mechanism movement under satisfied processing parameters are few.
特别是挤压铸造模CAE技术发展缓慢，而且研究内容主要集中在封闭型腔内的熔体流动成形过程分析，对满足成形工艺参数的模具机构运动的控制分析研究较少。 - Based on the analysis on the structure of the steering wheel made of magnesium alloy, and the design principle of the gating system, top casting, ring casting and aside casting forms are designed by mean of UG.
在对镁合金汽车方向盘压铸工艺分析的基础上，根据浇注系统的设计原则，采用UG软件设计了顶注浇铸系统、环形浇铸系统和侧注浇铸系统三种浇注系统。